No risk to you. Your 100% Satisfaction is Guaranteed with our 30 Day "No Questions" Money Back Guarantee. Hassle-free returns & exchanges.
The Petsafe In-Ground Fence combines the waterproof PetSafe Deluxe UltraLight containment receiver collar with a buried perimeter wire and a small transmitter that lets your dog know that he should stay in your yard. The collar features 4 adjustable levels of static correction plus tone-only mode for training to help you find the right level for your pet. Additional built-in safety features will keep you confident that your pet is playing safely in your yard.
Features:
For dogs 8 pounds and up
Fits neck sizes 6 to 28 inches
Four adjustable levels of static correction
Tone-only mode alerts your pet with a beep
Covers up to 1/3 acre with included boundary wire
Expandable up to 10 acres with additional wire (sold separately)
You set the boundary by burying wires around the perimeter of your yard. Your dog wears a collar that picks up the signal from the transmitter. As your dog nears the boundary wires, a beep alerts your dog, giving them a chance to stop without any correction. For those that continue, a safe static correction reminds them to stay in the area you have established. Simply adjust the correction level if your dog continues to test the boundaries.
Additional safety features help keep her in your yard more than before. Anti-Linger Prevention keeps your pet from staying in the Warning Zone for long periods of time and draining the battery. Progressive Run Through Prevention works by increasing the correction if your pet tries to quickly run through the boundary zone.
System Includes:
Transmitter with power adapter and mounting bracket
Troubleshooting Your In-Ground Fence ("Short Loop Test"):
If you are having an issue with your containment system, such as your pet has gotten in or out of your containment area without getting a static correction, you may need to perform what is referred to as a short loop test. A short loop test helps determine whether you are having a problem with your in ground wire or with your equipment.
Begin by unplugging your containment transmitter and open the lid. Disconnect your boundary wire and your ground wire if one exists. Set your boundary control width knob to 10. There is a switch on the side of your transmitter. If it reads "A, B, C," set the switch to B. If it reads "High/Low," set the switch to High.
Cut a length of wire that is between 10 and 12 feet long and strip the wire coating off each end. Take this wire loop and connect each end to the two boundary wire terminals. Now plug your transmitter back in.
If your loop light is not lit and your transmitter starts beeping, check and make sure that the wire loop ends are snugly within the terminals. If they are and your loop light is still on, and your transmitter is beeping, there is an issue with your transmitter.
If the loop light is on and your transmitter isn't beeping, your transmitter is working fine, and you should test the receiver collar as follows.
Loosen the collar probes. Attach each end of the wire on the included Collar Test Light to one of the probes underneath the exposed piece. Go to your transmitter and your short wire loop. You may have to get as close as six inches to the transmitter and wire to test the receiver collar.
When you are testing, the receiver collar should beep and your light should illuminate. If it works, your receiver is functioning properly.
If it doesn't, check your battery in your receiver collar. Make sure it is fresh and properly installed.
If the battery is fresh and installed correctly, and the test still doesn't work, it means there is something wrong with your receiver collar.
If your transmitter and your receiver collar both test okay on the short loop test, but you are still having an issue (such as your receiver collar not activating whenever it gets near the boundary wire), you may have another issue such as a wire break. At this point you should walk the containment area boundary and make sure that there isn't any activity that has disturbed your wire, such as digging or trenching. You should also check any area where you have spliced wire within your wire layout. Wire breaks tend to happen at splices, so check them and make sure no water damage or corrosion has occurred. If it has, redo your splices.
GUN DOG SUPPLY - "Serving Hunting & Field Dog Owners Nationally Since 1972."
Order online via Secure Server or call 1-800-624-6378 to order! GDS Warehouse, 17645 U.S. Highway 82, Mathiston, Mississippi, 39752 USA.
